Skip to main content

Menu

Back

New 995 Reversible Plow

Primary Tillage

995 Reversible Plow

Key Features

  • Moldboard frame pivots with the bottoms
  • Plastic moldboard and steel shins
  • Landsides with wedges
  • Front gauge wheels

Features

995 mainframe 995 mainframe

The V-style mainframe of the 995 Moldboard Plow distributes weight for good penetration.

 

The mainframe is made of high-strength 178-mm x 102-mm (7-in. x 4-in.) tubing that is 8-mm (5/16-in.) thick to handle the stress of high-horsepower tractors working in tough ground conditions.

Moldboard frame Moldboard frame

All 995 Moldboard Plows use only one set of bottoms.

 

The moldboards are reversed laterally by a hydraulic cylinder that is standard equipment. There are several advantages of this design over traditional two-way roll-over plows with two sets of bottoms:

  • Requires less 3-point hitch capacity
  • Requires less ballasting of the tractor front end
  • Eliminates initial cost and service requirements for one complete set of standards and bottoms

Integral on-land hitch Integral on-land hitch
#

The integral hitch gives unexcelled maneuverability in turns and when parking in tight areas:

  • Category 3/3N Quik-Coupler compatible
  • Tractor rockshaft lever controls the raising and lowering of the plow
    • Maximum plowing depth to 356 mm (14 in.)
  • Provides ample clearance between the tractor tires and the plow

Front gauge wheels Front gauge wheels

The front gauge wheels can be adjusted to limit the plowing depth to 356 mm (14 in.). They come equipped with 6.70-15 tires.

995 Moldboard Plow rear gauge wheels 995 Moldboard Plow rear gauge wheels
#

Two front and one rear gauge wheels are standard equipment on the 995 Moldboard Plow:

  • Equipped with 6.70-15 tires for good flotation
  • Easy turnbuckle adjustment on rear gauge wheel
  • Adjustable front gauge wheels limit the plowing depth to 356 mm (14 in.)

Promotions

Key Specs

Hitch

No. of bottoms

Total width of cut

Weight (approximate)

Clearances

Standards

Coulters

Bottoms

Frame

Horsepower required

Landing

Gauge wheel

Tires

Trashboards

Additional features

Additional information

Accessories and Attachments

Bottoms

Steel shins Steel shins

Steel shins are available as a field-installed option only.

 

The frog is pre-drilled at the factory to accept this attachment.

 

With this attachment, the steel shins will allow longer wear life when soil first comes into contact with the plow, but still offers the option of a plastic moldboard for sticky soil conditions.

Hydraulic Cylinder

  • Hydraulic Cylinder - BP16287

Landsides

Double landsides Double landsides

Double landsides allow converting five- and six-bottom plows equipped with wedges for operation in hard ground conditions.

 

The bundle includes one extra set of landsides for the front bottoms, four regular large landsides for the rear bottom, and all necessary attaching hardware.

Double landsides Double landsides

Double landsides allow converting five- and six-bottom plows equipped with wedges for operation in hard ground conditions.

 

The bundle includes one extra set of landsides for the front bottoms, four regular large landsides for the rear bottom, and all necessary attaching hardware.

Landsides with wedges Landsides with wedges

This bundle is for five- or six-bottom plows. It allows converting five- or six-bottom plows equipped with double landsides for operation in average-to-soft soil conditions.

 

The bundle includes a set of wedges for all bottoms, one set of extra-large landsides for the rear bottom, and all the necessary attaching hardware.

 

NOTE: Due to line-of-draft characteristics, the seven- and eight-bottom plows do not require use of wedges.

Landsides with wedges Landsides with wedges

This bundle is for five- or six-bottom plows. It allows converting five- or six-bottom plows equipped with double landsides for operation in average-to-soft soil conditions.

 

The bundle includes a set of wedges for all bottoms, one set of extra-large landsides for the rear bottom, and all the necessary attaching hardware.

 

NOTE: Due to line-of-draft characteristics, the seven- and eight-bottom plows do not require use of wedges.

Warning Lights and Emblem

  • SMV Security Emblem - BP16365
  • Warning Lights - BP16298

Wheels and Tires

Front gauge wheel Front gauge wheel

Front gauge wheels can be added to control the plowing depth.

  • Can be adjusted to limit the plowing depth to 356 mm (14 in.)
  • Equipped with 6.70-15 tires
  • Stihl
  • John Deere